How To Build and Install DIY Frameless Kitchen Cabinets // Home Bar Pt. 1

How To Build and Install DIY Frameless Kitchen Cabinets // Home Bar Pt. 1

Learn how to build DIY frameless kitchen cabinets using pocket holes and plywood! I’ll also show you how to apply edge banding, add soft close doors, and install the upper and base cabinets. Thanks to Krazy Glue for sponsoring this video, learn more about Fast Dry Wood Glue here : #sponsored

Next week’s video will be on building and installing the drawers using Blum Tandem Undermount Slides, so get SUBSCRIBED!

📦 Materials Used On The Cabinet Build (affiliate):

Krazy Glue Fast Dry Wood Glue :
Columbia Forest Products TouchWood Panels :
FastCap FastEdge Edge Banding :
General Finishes Enduro Black Poly :
Blum Undermount Slides :
Blum Soft Close Hinges :
Cabinet Levelers :
Edge Pulls :
NewAir ABR-1770 Mini Fridge :
GRK Cabinet Screws :

🛠 Tools Used On The Cabinet Build (affiliate):

🔹 Rockler Countersink Bit Set :
🔹 Rockler Undermount Jig :
🔹 Rockler Hinge Mounting Plate Jig :
🔸 Powermatic PM1500 Bandsaw :
🔺 Infinity Tools ½” Bit :
Kreg Foreman Pocket Hole Machine :
Kreg Concealed Hinge Jig :
Kreg Corner Clamp :
Kreg K5 Pocket Hole Jig :
Kreg Micro Drill Guide :
FastCap Flush Trim Cutters :
FastCap Quad Trimmer Pro :
FastCap Speed Roller :
FastCap Speed Break :
Table Saw :
Push Stick :
Miter Saw :
Speed Square :
Magnetic Screw Holder (for my impact driver) :
Cordless Drill :
Brad Nailer :
Japanese Pull Saw :
Block Plane :
Line Laser :

👕 Get your Build It Yourself merch!







Crafted Workshop says:

Hope y'all enjoyed part 1 of the home bar series! Go ahead and get subscribed so you don't miss the upcoming videos : // Thanks to Krazy Glue for sponsoring this video, learn more about Fast Dry Wood Glue here :

John Sumner says:

This looks amazing. Since you painted them all black, why didn't you do shou-sugi ban?

Michael Marino says:

Can you share the plans?

Tom Fitzsimons says:

Set your laser 20mm/1inch above your finish height… then using an offcut with a thin pencil line marked on it you are able to level the unit front and back.

Jordan Eustache says:

Where's the link for that awesome hole saw?

diycentral says:

Really nice looking project. 12:30 I'm sure you know about the straight edge trick for aligning both clips at the same time. Saves a lot of time when doing a lot of doors.

Robert Kripaitis says:

What brand of HVLP sprayer did you use to apply the finish?

wsender says:

Meehan's Bartender Manual is suuuuuch a good book. Looks like you're a bit of a cocktail wonk. Too bad NC ABC's are awful 🙁

Skibble Dazzle says:

I did a huge DIY project building cabinets … but all my cabinets broke destroying all my cutlery and porcelain into a huge bang in front of my posh dinner guests.

no, none of that happened. Still risky though.

Huy Nguyen says:

his work makes me just wanna go to ikea and buy the damn cabinet

Marc Siegel says:

great video. Thanks! Do you have a rough idea how much the project cost. Or if this is cheaper than buying pre built cabinets. Thanks again

DaBuick says:

if you shine your laser on a stud, you don't have to transfer!

Julio Ortega says:

I call this art

Robbie Pastrana says:

What is the name of the program used to design it all?

Morgan Sandqvist says:

Looks really great – i would consider having the same grain direction on both doors and drawers.

Connor Pearson says:

I think the alcohol costs more than whats holding them!

Christian Mercado says:

amazing job

Ayhan Kuzay says:

this is great job . but , There is only one problem. direction of cabinet door 🙁

Noob says:

Awesome! But it looks nicer with the original colour rather then black

Comments are disabled for this post.